1. Silicone Material Introduction

Why the Surface Under the Lash Line Matters

Every lash decision begins with the face it sits on. TPE, a thermoplastic elastomer softened with mineral oil, stays slightly tacky and slightly porous. Platinum-cure silicone is denser, non-porous and holds fine molded detail such as a lid crease or tear duct.

On TPE, water-based glue sets slowly because the surface resists a dry bond. On silicone it grabs faster and releases more suddenly, so a small error can pull paint. Neither material tolerates solvent-heavy removers.

Silicone vs TPE at a Glance

The table below covers the head, where lashes live, though the traits run through the whole body.

Our comparison of silicone vs tpe sex doll construction goes further on density, seams and repairability.

Adhesive That Is Compatible With TPE and Paint

For most TPE heads a latex-free water-based lash adhesive is the safest first choice. It cures flexible, releases with warm water and does not attack paint. A neutral-cure silicone adhesive holds heavy bands more firmly, but use pinhead amounts and allow 12 to 24 hours.

Avoid cyanoacrylate. It dries hard, can frost surrounding TPE with a white bloom and often takes paint with it. Solvent removers sold for human lash extensions are just as risky on a painted face.

2. Customization Options

Strip Lashes or Individual Clusters

A strip is one band and installs in a single pass, which suits a doll that is displayed more than handled; expect about ten minutes per eye. Individual clusters take 30 to 45 minutes per eye, sit closer to the lash line and can be replaced one section at a time.

If you keep several pairs of sex doll eyelashes in rotation, strips are cheaper to swap for a seasonal look and easier to store flat.

Length, Curl and Volume

Length should follow the eye opening rather than the trend. Most TPE heads have an opening of roughly 24 to 30 mm, where an 8 to 12 mm lash sits in proportion; at 14 mm and beyond the face reads as costume on a 140 cm or 150 cm body.

Curl changes the silhouette as much as length. A C or D curl lifts away from the lid and catches on wigs; a J or B curl stays closer and photographs naturally. Volume should stop short of the brow, or a dense 3D band hides the painted lid crease.

Band Type and Color

A clear or thin black band disappears against a painted lash line. Cotton bands drape around a curved lid; plastic bands keep their shape but resist bending to the socket. Soft black and brown flatter pale faces, while jet black suits high-contrast styling.

Brows, liner and blush follow the same restraint, as our guide to sex doll makeup explains.

3. Buying Guide

A Starter Kit With Numbers

Everything below fits in a small tray and covers roughly a year of restyling.

A complete kit lands between about $45 and $120. Prices move with brand and region, and shipping is quoted separately.

Matching Lashes to Doll Height

Body size predicts eye opening better than any product label, so measure once and buy to that number.

Price Bands and Budget Reality

Entry TPE bodies typically list 12 to 16 articulation points, while premium frames advertise 24 or more. Joint count matters here for one reason: a neck that tilts and locks is easier to work on than one that flops mid-install.

Replacement heads run roughly $150 to $450 depending on material, paint work and whether the eyes are inset. Full bodies sit between about $600 and $2,000 in TPE and $1,500 to $5,000 in silicone. Those ranges exclude freight, duties and taxes. This is general information, not financial advice.

4. Maintenance & Care

Step-by-Step Installation

1. Wipe the lash line with a cotton swab dampened with isopropyl alcohol and let it dry for five minutes.
2. Trim the band from the outer end until it covers about 90 percent of the lid.
3. Dry-fit the lash, mark the outer corner and flex the band around a fingertip to soften its curve.
4. Run a thin line of adhesive along the band and wait until it turns tacky.
5. Seat the band one to two millimeters above the painted lid edge, center first.
6. Press for 20 to 30 seconds with a clean finger or a brush handle.
7. Check angle and symmetry in a mirror at eye level before the adhesive sets.
8. Leave the head undisturbed while the glue cures.

Curing and the First 24 Hours

Water-based adhesive reaches a usable bond in 20 to 30 minutes but keeps firming for hours. Leave the head face-up and avoid wigs or storage bags for the first day. Silicone adhesive needs a full 12 to 24 hours. A hair dryer on low, held 30 cm away, speeds curing; direct heat softens TPE fast.

Removal Without Lifting Paint

Hold a warm damp cloth against the closed lid for two to three minutes, then peel from the outer corner inward with slow pressure. Never pull upward against the lid. If the band resists, add warmth and water rather than solvent, and work a cotton swab under it a few millimeters at a time.

Eye-Socket and Eyelid Care

Clean the lid after removal, but keep fluid out of the socket; a dry swab lifts adhesive residue without pushing moisture behind the eye. Inset eyes need an occasional dust-off, while the surround needs more care than the eyeball itself, as our notes on sex doll eyes explain.

Once a month, wash the face with mild soap and lukewarm water, rinse, pat dry and re-powder the TPE. Our walkthrough on how to clean tpe sex doll covers the sequence, including why less powder is more around painted features.

5. Shipping & Privacy Policy

Packaging and Discretion

Orders ship in a plain carton with no brand markings, product names or photographs, and the card descriptor is deliberately neutral. Discretion ends at the border, though: customs officers may open and inspect a parcel, and inspection sits outside any retailer's control.

Delivery Windows and Inspection

In-stock items usually leave the warehouse within two to five business days, and transit commonly runs 7 to 20 business days. Made-to-order paint adds time. Photograph the carton before cutting tape and report damage within 48 hours.

Payment, Age Verification and Import Rules

Buyers must be 18 or older, and some payment providers restrict adult merchandise, so available methods vary by country. Duties, taxes and import eligibility are set by the destination country, and border outcomes are never guaranteed. This is general information, not legal advice.

6. Trust & Guarantee

What a Warranty Covers

A workmanship warranty normally covers mold defects, seam separation, skeleton failure under normal use and paint faults present on arrival. It rarely covers solvent contact, heat exposure, adhesive residue, dye transfer or handling beyond the material's limits.

Damage, Returns and Exclusions

Report transit damage with photographs of the carton and figure inside the stated window. Hygiene rules restrict returns on opened intimate products in many jurisdictions, so packaging condition matters. A replacement head is often the practical fix when only the face is affected.

Support That Answers Fit Questions

Before ordering, ask for the eye-opening measurement, the paint type and the neck mount specification. A retailer who answers those three in writing can also advise on lash length, adhesive and removal. Treat claims of official brand licensing with caution.

Frequently Asked Questions

Final Thoughts

Lashes change a face more than their size suggests, and the install is forgiving when preparation is not rushed. Degrease, trim, dry-fit, apply a thin line of water-based adhesive, and let it cure undisturbed.

Buy two pairs in the length that suits your doll's eye opening rather than five from a photograph. Keep removed bands clean and flat, and replace a tired lash rather than re-gluing it.